Arlington sits in one of the more hail-prone stretches of the country, wedged between Fort Worth and Dallas in a corridor that meteorologists half-jokingly call part of "hail alley's" eastern reach. Alpine Exteriors works on siding across Tarrant County neighborhoods — from the brick-and-siding combinations common in Meadowbrook and Lake Arlington to the newer vinyl and fiber cement builds out toward South Arlington and the Rush Creek area. The work here isn't generic exterior remodeling; it's driven by a specific set of stresses that Arlington's climate and soil put on a home's cladding, and the siding choice, fastening method, and installation sequence all change because of it.
Most siding calls in Arlington fall into one of two buckets: storm-related replacement after a hail or wind event, and proactive replacement on a home where the existing siding — often builder-grade vinyl from the 1990s or 2000s — has reached the point of cracking, fading, or pulling away from the wall. Both jobs require the same starting point: an honest look at the sheathing and house wrap underneath, since siding is only as good as what it's fastened to.
Four things drive nearly every siding decision in Arlington:
There's no single "best" siding for Arlington — the right call depends on the home's exposure, budget, and how much maintenance the owner wants to take on.
The City of Arlington's Building Inspections division requires a permit for most siding replacement projects, particularly when the job involves removing siding down to the sheathing, repairing structural framing, or changing the exterior material or footprint. Straightforward panel repairs on a small section sometimes fall under exemptions, but replacing siding on an entire elevation or the whole house typically triggers a permit and at least one inspection. Alpine Exteriors pulls these permits as part of a full replacement rather than leaving it to the homeowner, since an uninspected job can create problems at resale or with an insurance claim later.
If the home is in a subdivision with an active homeowners association — common throughout Arlington's newer developments — HOA architectural approval is a separate step from the city permit, and it can be the slower of the two. HOAs frequently restrict siding color and, in some cases, material type, so it's worth checking those covenants before ordering material. For storm-damage jobs tied to an insurance claim, we also coordinate timing so the adjuster's inspection and the permit application aren't working against each other.
Siding replacement in Arlington generally runs in the range of $9 to $16 per square foot installed for fiber cement, and roughly $5 to $9 per square foot for standard vinyl, with impact-rated vinyl and engineered wood landing in between. A full single-story home replacement often lands somewhere in the low-to-mid five figures; two-story homes with more complex trim work or extensive rot repair underneath the old siding push higher. These are ranges, not quotes — the actual number depends on square footage, how much sheathing needs replacing, trim and soffit condition, and how much of the old material has to come off versus being covered.
Two Texas-specific cost factors show up more here than in milder climates. First, Texas homeowners insurance policies commonly carry a separate wind/hail deductible, often a percentage of the dwelling coverage rather than a flat dollar amount — that can mean a $6,000-$15,000 out-of-pocket portion on a hail claim depending on the policy, which changes how homeowners approach a storm-damage job compared to a proactive one. Second, choosing Class 4 impact-rated material can sometimes reduce future wind/hail premiums, which is worth asking your insurer about before finalizing material choice, since it can offset some of the higher upfront cost over time.
Cracks, punctures, and holes are clear damage. Bruising or granule loss on fiber cement paint film, and small dents in vinyl, are less obvious but can still compromise the material's ability to shed water over time. A physical inspection is the only reliable way to tell — photos from the ground often miss it, especially on upper stories.
That depends on your carrier, your policy language, and often on whether matching material for a partial repair is still available. Some Texas policies include matching-material provisions that support a full-elevation or whole-house replacement if the exact original product is discontinued; others don't. We can document damage for your adjuster, but coverage decisions come from your insurer, not from us.
A typical single-story home runs about one to two weeks from tear-off to final trim, weather permitting. Spring and early summer — peak storm season — is also peak scheduling season for every siding contractor in the Metroplex, so timelines stretch during that window.
Not necessarily — it's a legitimate budget option, especially on shaded elevations. The trade-off is real: standard vinyl is more prone to heat warping on unshaded west- and south-facing walls and more likely to crack under a significant hail hit than fiber cement. If budget is the main driver, impact-rated vinyl on exposed sides paired with standard vinyl elsewhere is a reasonable compromise worth discussing.
Whether you're dealing with hail damage that needs to be documented for a claim, siding that's warped after another Texas summer, or you're simply planning ahead of the next storm season, Alpine Exteriors can walk your property and lay out real options and real numbers before you commit to anything. Contact Alpine Exteriors to schedule an on-site look at your Arlington home's siding.